AQUA SEAL DAMP COAT

Whatsapp Video TDS
Category:

Description

BD  AQUA  SEAL DAMP COAT  is a high performance two – component, water dispersible, epoxy resin coating, designed to  provide a hard, semimatt seal to    concrete  floors, walls, ceiling and other substrates.

APPLICATIONS

BD AQUA SEAL DAMP COAT is used as general protection coating  for floors or walls in   many applications including:

SOG drink and beverage production areas. Industrial    and  commercial kitchen walls. Warehouses. Hospitals   and  pharmaceutical  factory walls. Fish  and  meat   processing plant walls.

General food processing and  manufacturing  plants. Light vehicular traffic areas.

ADVANTAGES

  • Water based, moisture tolerant.
  • Solvent free, non -tainting.
  • Dust free surfaces.
  • Available in a wide range of attractive colours.
  • Cost effective.
  • Good chemical and mechanical resistance.
  • Easy application.
  • Resistant to fungal attack.

The second coat may be applied as soon as the first coat has initially dried. Drying time will depend on the substrate and the ambient conditions. If the over coating time is exceeded the first coat must be abradwedith sandpaper prior to theapplication of the second coat.

Adequate ventilation must be provided to ensure thantecessary drying & curing of the material is achieved.

TECHNICAL PROPERTIES:
Specific gravity: 1.4 ± 0.05 g/cm3
1 hr @ 35oC
Pot life: 2 hr @ 25oC
Minimum time 4 hr @ 35oC
between coats:
Maximum time 24 hr @ 35oC
between coats:
Volume solids: 75 – 80%
Dry film thickness/
coat: 80 – 100 micron
1 day for light foot traffic
Curing time: 7 days for full chemical
resistance
VOC: < 20 g/ltr

METHOD OF USAGE

The substrate must be clean, dry, even, dense and free from oil, grease, dust and other contaminants. A clean    surface     will     ensure     maximum      adhesion between the substrate and the coating.

To avoid inconsistent workability and pot life, make sure that the materials to be used are stored in shaded area and protected from extremes of temperatures, for at least 24 hours prior to application.

Use brush or lamb’s wool roller, or airless spray machine   to apply the mixed BD AQUA SEAL DAMP COAT on the prepared surfaces.

Apply  2  coats  of    BD  AQUA  SEAL  DAMP  COAT     at  6 m² /kg/coat,  second  coatshould  be  applied   at   a   right angle to the first coat.

REMARKS

 Highertraffic areasshouldreceiveextra coatsor a higherbuildsystem.

BD AQUA SEAL DAMP COAT    not be appliedat temperatures below 10°C or where ambient relative humidityexceeds 85%.

BD AQUA SEAL DAMP COAT    not beappliedon to surfacesknown to suffer from risingdamp.

In caseof sprayapplications,airless spraymachines shouldbeused.

CLEANING

 

Tools and equipment can be cleaned with clean water when it is wet. Dried BD AQUA SEAL DAMP COmAaTy

be removedwith YASH-Solvent.

PACKAGING

 

BD AQUA SEAL DAMP COisAaTvailable in 1 KG ,10KG.

COVERAGE

 

The coverage rate is 5- 6 m² /kg/coat to achieve dry film thicknessof 90- 110 microns/coat.

STORAGE

 

Store in a dry area out of direct sunlight at temperatures between5°Cand 35°C.

SHELFLIFE

 

BD AQUA SEAL DAMP COhAasT a shelf life of 9 months from dateof manufacture if stored in proper conditions and un- openedpacks.

CAUTIONS

HEALTH AND SAFETY

 

BD AQUA SEAL DAMP COshAoTuld not come in contact withskin and eyes.

In caseof accidentasl plashesto theeyes,rinsethoroughly with clean water and seek medical advise. Suitable protectiveglovesandgogglesshouldbe worn. Donotuse solventto cleanBD AQUA SEAL DAMP COfrAomT skin.

For further information refer to the Material Safety Data Sheet.

FIRE

 

BD   AQUA   SEAL   DAMP   COiAsT water   based  and nonflammable

Reviews

There are no reviews yet.

Be the first to review “AQUA SEAL DAMP COAT”

Your email address will not be published. Required fields are marked *

Go to Top